Contents

Addressable sensors

In a nutshell. Individual sensors are fastened to the fence or buried in the ground, each responsible for its own small section (from 3 to 50 m) and "knowing" its place in the line. The processing unit sees exactly which sensor was triggered — so the system pinpoints the location of a breach even in a difficult interference environment. VD-3, VD-5 and VD-5-K are vibration sensors on the fence (MEMS accelerometer), SD-3 is a seismic sensor in the ground, DD-1 is an addressable amplifier for triboelectric cable.

They can be combined — but it is not required. Vibration, seismic and optical detectors can be joined on one site into a single system: vibration detectors register contact with the fence, seismic ones — approach to the perimeter and excavation work, optical ones monitor the zone without contact. Addressable sensors cover the vibration and seismic security lines, including long ones, through BOS-L linear units; they can be supplemented with optical IR detectors (ID, IKS, TIS, IVA) — for example, at wickets, gates or sections with no clear zone. But this is not mandatory: the addressable system works on its own.

Addressable sensors connect to the control units over RS-485 lines — directly or via a fiber-optic communication line using BOS-L linear processing units. This is how a long, sensor-rich security system is built with a minimum of cable routes.

Device Purpose Protected zone of one sensor Detection accuracy Transport security certificate Extended frequency range Spectral subtraction
Vibration addressable VD-5 Mesh, profiled-sheet and wooden fences 3–9 m 3–9 m Yes No Yes
Vibration addressable VD-5-K Mesh, profiled-sheet and wooden fences 3–9 m 3–9 m Yes Yes Yes
Vibration addressable VD-3 Mesh, profiled-sheet and wooden fences 3–9 m 3–9 m No No No
Vibration addressable extended DD-1 Razor tape, soft coping arms 2 arms of up to 30 m (per data sheet) 30 m Yes No No
Seismic addressable extended DD-1 Ground under the fence 2 arms of up to 30 m (per data sheet) 30 m Yes No No
Seismic addressable SD-3 Hidden security line in the ground 5 m 5 m Yes No Yes

Thanks to the high detection accuracy and the small protected zone, addressable sensors work together with a spatial-temporal data-processing algorithm. The system:

  • determines localised actions on the fence by comparing energy levels between sensors in comparison zones;
  • matches the action against the intruder profile: compared with the reference test climb-over and data from neighbouring sensors, it determines the target type (person, vehicle, animal, bird) and whether the effort applied is sufficient to get over the fence;
  • assesses the noise level of the environment from global actions affecting several fence fragments — for example, rain or wind;
  • analyses the uniformity of the noise environment around the perimeter as a whole and in the comparison zones in particular — on this basis it suggests adjusting the sensitivity: reducing false alarms or raising the detection level;
  • detects signs of deliberate jamming, of imitators planted in the communication line, and potential system defects.

The spatial-temporal comparison algorithm makes it possible to tell a person's impact on the fence from a wind gust or heavy hail: a person acts on the fence at a single point, while rain or hail acts on several sections at once.

Each sensor is configured individually:

  • gain factor;
  • lower working-frequency bound — from 1 to 100 Hz;
  • upper working-frequency bound — from 100 to 400 Hz;
  • spectral subtraction of the interference signal (switchable);
  • 25/50/75 Hz notch filter;
  • diagnostics of dangerous actions: opening the sensor, fence deformation (including cutting mesh), falling or a change of tilt angle;
  • self-diagnostics of the sensor and of the sensing element.

The wide frequency range allows confident operation on different fence types even in a difficult interference environment.

Vibration sensors VD-3, VD-5, VD-5-K

The sensors are fastened directly to the fence and measure its vibration level — the energy applied to it. Local sensitivity allows choosing installation points flexibly — for example, at wickets or gates — and reduces the influence of vibrations of loosely fixed sections relative to the support posts.

The sensing element is a high-precision high-speed MEMS accelerometer with virtually no analogue path: the sensors can be installed close to sources of radio interference — radars, beacons, generators, transformers, high-voltage lines.

VD sensors are mounted on mesh and wire fences, fences of thin boards, pickets, thin metal (profiled sheet) or polycarbonate — the perimeter is protected both against climbing over and against destruction (cutting, bending back).

Recommended installation spacing:

  • solid "profiled sheet" fencing — every 5–10 m;
  • mesh fencing — on every section, roughly every 3 m;
  • interconnected sections — every other one, roughly every 6 m;
  • wooden and other non-solid fences — every 5 m;
  • collapsible coping arms and deformable obstacles — every 5–10 m.

Installation comes down to connecting two twisted-pair cables and fastening the housing to the fence with the supplied plates. The mounting screws are under the sensor's cover — it cannot be removed without opening the housing, and an optical tamper with an active strobing reference-level source generates a notification of an opening attempt. The housing is potted with transparent silicone — protection against aggressive external environments.

The cable is not a sensing element, so the sensor can be placed anywhere on the fence and the cable routed in whatever way is convenient: inside the fence, in a tray, or fastened externally with cable ties.

Seismic sensors SD-3

SD-3 converts ground vibrations caused by an intruder's actions into an electrical signal by the piezoelectric effect. A special mechanical signal amplifier operating across the entire band of processed frequencies provides the highest sensitivity.

A 5 m installation spacing guarantees detection of an intruder in any weather and in any soil type — even with partial waterlogging.

The sensors can be placed:

  • in front of or under the fence — recording the intruder's approach even before they touch the fence;
  • inside the guarded perimeter — confirming the fact of penetration;
  • anywhere detection of people or vehicles matters, regardless of physical barriers — including for forming a hidden security line.

Triboelectric sensors DD-1

DD-1 is an addressable preamplifier for the TD-1 triboelectric cable: it processes the signal from two inputs and passes it to the BOS-L linear unit. Up to 30 m of cable is connected to each input (per data sheet), so one unit covers up to 60 m of perimeter; the detection accuracy corresponds to the length of one arm — 30 m.

The TD-1 cable converts fence vibrations into an electrical signal by the triboelectric effect. This is the simplest and most affordable sensing element: installation means fastening with cable ties to the protected surface, and a damaged section can be restored without special tools.

Three application options:

  1. On mesh, wire, wooden, metal (profiled sheet) or polycarbonate fencing — protection against climbing over and destruction (cutting, bending back).
  1. On spiral razor-wire (AKL) screens, tin or polycarbonate coping arms — protection against climbing over with a ladder and guarding solid concrete and brick walls.
  1. In the ground — an anti-tunnel security line: the cable detects a person with a spade at 1–5 m (depending on the soil and settings), and excavation work with heavy machinery — up to 30 m. Suitable for guarding underground utilities.

Technical Specifications

Values are taken from the data sheets dated 24.07.2026.

Vibration sensors VD-5, VD-5-K

Parameter Value
Sensor type MEMS accelerometer
Supply voltage range 12–30 V
Power consumption not more than 60 mW
High-pass filter cut-off (adjustable) 4, 12, 25, 50 Hz
Low-pass filter cut-off (adjustable) 50, 100, 200, 400 Hz
Band-pass filter: centre frequency / bandwidth 25, 50, 100 Hz
Gain adjustment range (Ku) 0–35 dB, step 5 dB
Sensitivity zone not less than a standard fence section
Line output RS-485
Recommended cable FTP 2×4×0.5 outdoor
Dimensions not more than 120×60×35 mm
Mass not more than 160 g
Operating temperature −40…+50 °C

Seismic sensor SD-3

Parameter Value
Sensor type Piezoceramic
Supply voltage range 12–30 V
Power consumption not more than 60 mW
High-pass filter cut-off (adjustable) 4, 12, 25, 50 Hz
Low-pass filter cut-off (adjustable) 50, 100, 200, 400 Hz
Band-pass filter: centre frequency / bandwidth 25, 50, 100 Hz
Gain adjustment range (Ku) 10–45 dB, step 5 dB
Sensitivity zone (dry loam, vertical installation) circle with a radius of 2.5 m
Line output RS-485
Recommended cable FTP 2×4×0.5 outdoor
Dimensions Ø 60; h = 48 mm
Mass (without cable) not more than 225 g
Operating temperature −40…+50 °C

Triboelectric sensor DD-1

Parameter Value
Supply voltage range 12–30 V
Power consumption not more than 200 mW
Line output RS-485 (line load 1/250)
Gain adjustment range (Ku) 0–35 dB
Health monitoring continuous, remote parameter control
Cable diameter through the cable entry 5–8 mm
Reverse-polarity protection / housing tamper detection yes
Operating temperature −40…+50 °C

Linear processing unit BOS-3-0 (BOS-L)

Parameter Value
Supply voltage range 8–30 V
Power consumption (without connected equipment) not more than 2 W
Maximum addressable sensors per line 120 (RS-485)
Communication ports 2× RS-485, Ethernet (LAN)
Mean time between failures 60,000 h
Mass not more than 0.20 kg
Operating temperature −40…+50 °C

Documentation

Device Passport (PS)
VD-5 VD-5 PS
VD-5-K VD-5-K PS
DD-1 DD-1 PS
SD-3 SD-3 PS
BOS-L BOS-3-0 PS