Budget system Topol-1
In a nutshell. Topol-1 is the simplest and most affordable system in the line. The BOS-1 processing unit accepts signals from three types of sensing elements: VD-2 vibration sensors (piezo element, fastened to the fence), SD-2 seismic sensors (in the ground) and TD-1 triboelectric cable (it generates a signal itself when bent). It suits small perimeters, wickets, gates and budget-conscious sites.
Topol-1 is the optimal solution for budget perimeter security.
At the heart of the system is the BOS-1 signal processing unit. It accepts signals from three types of sensing elements and lets you combine them for a specific perimeter section, fence type and expected method of penetration.
Each of the two inputs is processed independently with separate alarm notification output — the detector has two separate protected zones.
The signal is split into 10 frequency bands in the 0.75–800 Hz range, each processed separately:
- an adaptive threshold is computed for each band, tracking the environmental noise — rain, wind and hail do not cause false alarms;
- the number of threshold crossings is counted for each band.
Then a "voting" procedure runs: crossings in the active frequency bands and their weight are taken into account when deciding whether to raise an "Alarm" notification.
The main distinction of BOS-1 is the flexible choice of operating subbands: two bands out of ten are enough for confident operation. The system is tuned to any fence type and keeps high sensitivity in a difficult interference environment, and the free software makes setup simple and clear.
Two inputs allow combining sensing elements. For example, at the transition from a mesh fence to a solid one: vibration sensors VD-2 on one arm, triboelectric cable TD-1 on the other:
A single detector can form two security lines in one protected zone: point vibration sensors VD-2 protect the fence from destruction (cutting, bending back), while cable TD-1 protects against climbing over by a prepared intruder with a ladder. Or: VD-2 against destruction, and TD-1 in the ground — an anti-tunnel security line:
The detector has two "Alarm" loops — one per protected zone — and a shared "Fault" loop. It can be connected directly to any receiving device with dry-contact inputs, for example Bolid Signal-10 or Signal-20.
Topol detectors are joined over the RS-485 interface with KX/EX bus collectors — this is how a perimeter up to 2400 m long is built.
To each detector input you can connect:
- up to 200 metres of triboelectric cable TD-1;
- up to 40 vibration sensors VD-2;
- up to 40 seismic sensors SD-2.
With a heating board, the operating temperature range widens to −55…+50 °C.
Triboelectric cable TD-1
TD-1 converts fence vibrations into an electrical signal by the triboelectric effect. This is the simplest and most affordable sensing element: installation means fastening with cable ties to the protected surface, and a damaged section is restored without special tools.
Three application options:
1) On mesh, wire, wooden, metal (profiled sheet) or polycarbonate fencing — protection against climbing over and destruction.
2) On spiral razor-wire (AKL) screens, tin or polycarbonate coping arms — protection against climbing over with a ladder and guarding solid walls.
3) In the ground — an anti-tunnel security line: detection of a person with a spade at 1–5 m, excavation work with heavy machinery — up to 30 m.
Vibration sensors VD-2
VD-2 converts fence vibrations into an electrical signal by the piezoelectric effect. Its main difference from the TD-1 cable is local sensitivity: the sensor reacts only over the section where it is installed. This allows choosing installation points flexibly (for example, wickets and gates) and reduces the influence of vibrations of loosely fixed sections relative to the support posts.
VD-2 is mounted on mesh and wire fences, fences of thin boards, pickets, thin metal (profiled sheet) or polycarbonate — protection both against climbing over and against destruction (cutting, bending back). We recommend a 5 m installation spacing or one sensor per fence section.
Seismic sensors SD-2
SD-2 converts ground vibrations into an electrical signal by the piezoelectric effect. A mechanical signal amplifier operating across the entire band of processed frequencies provides the highest sensitivity.
A 5 m installation spacing guarantees detection of an intruder in any weather and in any soil type — even with partial waterlogging.
The sensors can be placed:
- in front of or under the fence — recording the intruder's approach even before they touch the fence;
- inside the guarded perimeter — confirming the fact of penetration;
- anywhere detection of people or vehicles matters, regardless of physical barriers — including for forming a hidden security line.
Documentation
| Device | PS / RE / ET / IM |
|---|---|
| BOS-1 | PS |
| BOS-1 (system RE) | RE |
| VD-2 / VD-2-1 | PS |
| SD-2 / SD-2-1 | PS |
| TD-1 | ET / IM |
| VK-1 (vibration cable) | ET |
| MS coupling fitting | ET |
| US matching unit | ET |
| PU-V / PU-V-1 / PU-T / PU-T-1 amplifiers | PS |
| BOS-1 housings | ET (polycarbonate) / ET (aluminium) / ET (thermostatic) |